Veneer Reeling Machine - Plate Rolling Machine - Hi-sea

Veneer Reeling Machine

Veneer Reeling Machine

Veneer Reeling Machine

1. Veneer Reeling Machine Summary
    The veneer reeling machine can pre-bend the ends of plate, feed steel plate just one time, and then to pre-bend the ends of plate, roll the workspace to drums shape, don’t need to return. The working up roller is the main drive roller, the down rollers and side roller use hydraulic drive to do elevate movement. And move controlled by computer, horizontal adjust automatic, show by screen, the synchromesh accuracy attached ±0.2mm. Turnover and resume of flip-bearing used hydraulic to drive. Installed balance system on the ends of up roller, so it’s easy to unload work piece. Adopt mobile independence operator table, so can operator at any time and any place, the machine has safety interlock device. For a world it has high technology, overall function, high accuracy and easy to operator. So it’s the model rolling machine, it’s the first choice in energy, transport, fossil oil, chemical, shipbuilding, steel and some other industries.
    This machine composed of four working rollers, left and right rack of machine, base board, rolling rhombus tube function, turnover part, device part, sensor part, hydraulic system, electrical system and so on.

2. Mechanical Part of Veneer Reeling Machine
    Working roller is the main part of device. The material choice steel 50Mn, and stand every standard very serious. These can ensure the comprehensive mechanical performance.
    The base board and rock as the main parts of device, use wield structure. Do anneal treatment comply with arts standard, this can eliminate internal stress, so it has enough strength and steel performance. It can work on full load state.
    Up roller is the main drive roller, the motor drive with the help of speed reducer. The output spindle of motor installed braking device, so it can ensure fixed position accuracy. All above these ensure the whole body has enough strength, the main joints connector with key and melt, so it’s easy to install and repair.
    The down roller and side rollers do elevating movement drive by the ends oil vat. The ends bearings use axis adjustable roller bearings. Elevating synchronization controlled by computer. The turnover side of up roller installed turnover oil vat, the ends of up roller installed balance mechanism, so it’s easy to unload the work piece.
3. Veneer Reeling Machine Technical Parameters

    The technical parameter is optional, we can accommodate your requirements, please don’t hesitate to contact us!
The thickness of coiled plate: 10mm                                           
Pre-bend thickness: 8 mm                              
The width of the coiled plate: 2500mm                                       
Min diameter of the max model: 800mm                                        
Yielding limit of plate: 245Mpa                                   
Diameter of up roller: 330mm                                             
Diameter of down roller: 310mm                                           
Diameter of side roller: 230mm                                          
Rolling speed: about 4m/min                                     
Hydraulic system pressure: 18Mpa                                              
Main motor power: 15Kw                                                 
Machine weight: 14.5T

4. Advantages of Veneer Reeling Machine

    (1) Four roll plate rolls are more precise, productive, versatile, faster, safer and easier to operate than three roll machines. They are less dependent on operator competence. They are ideal for bending plates up to 90 mm thick.
    (2) The fastest and most accurate bends are made by four roll machines. The plate is held securely in place between the top and bottom rolls while the side rolls move vertically to create the bend.
    (3) The bottom roll moves up to hold the plate edge securely against the top roll while the side roll is raised to form an accurate pre-bend, minimizing the flat zone on the plate edge. Pre-bending on a three roll machine requires that plates be tilted down as they are being fed. In contrast, plates are loaded horizontally at the feed level for pre-bending on a four roll machine, which allows the ake place on either side of a four roll machine. If fed from only one side, they can even be placed up against a wall to save floor space.


 



 

Contact with us now

Our mail: hs@cqhisea.com

replace